Lou Katz @lou@entropyservice.com

I have a very old clothes dryer reaching the end of its life very rapidly. So when the START knob broke off quite sometime back, I didn't want to spend much to replace it. But due to the panel design and such, and the age of the dryer, I couldn't find anything that would fit that wasn't insanely expensive for a dumb knob (plus shipping). I've been starting the thing with a pair of pliers.

Time to try a practical print on the new Bambu Labs A1 3D printer? This is never going to work. But what the hell.

I look around and find a knob model already created that has several versions including one that looks like it might work, but it also might not fit, might just spin, and might just break off when you tried to turn it.

But it would be an interesting experiment.

Got the model, and just sliced it in Bambu Studio using the defaults (I have this running on a Chromebook in the Linux container). I expected a complaint about lack of support, because the knob's central cylinder meant most of the knob was just floating in the air.

Yep, support warning comes up.

I click one checkbox for supports. Didn't change any values.

Yeah, the graphics show it has to create a LOT of support material to hold that thing up. But it claims only 1.25 hours to print.

So I let it print.

Finished, I pop it off the plate and it looks like a flying saucer. Heavy support material under and around it. I can't even flex it with my fingers.

I grab a pair of pliers and start pulling on the support material. It actually seems to be tearing loose around the knob body. I'm left with the knob and some support material underneath to peel off.

But the hole in the center, that is supposed to fit around switch shaft and grab it, looks too large and also is full of plastic. Lovely.

But hmm. There seems to be an almost invisible line there. I take a tiny screwdriver and pry a little bit. The entire plug of plastic pops out leaving the appropriately shaped hole. The precision involved is scary.

Eyeballing it, the hole looks too large and I expect it to spin on the shaft, and I'm already thinking of what I could stuff in there to stop the spinning.

But might as well see. I put the knob on and it seems to spin freely as I feared, then suddenly drops down into place. Huh?

And it works. First try. And it actually looks decent as well. How long will it work? Seems solid right now, and is very likely to outlast the dryer given the dryer's overall condition.

No Star Trek warp drive. But at least we have replicators now.

Welcome to the 21st century.

L

Did you know it used to be illegal for a company to buy back its own stock? It was understood to be stock price manipulation. (Because it is.)

Reagan's "deregulation" changed the rules in 1982.

Like everything else, companies now pay politicians to keep it the way it is.

#deregulation #reagan #corruption

New Israeli Road in Gaza Suggests Plan for Permanent Occupation, Analysis Finds https://truthout.org/articles/new-israeli-road-in-gaza-suggests-plan-for-permanent-occupation-analysis-finds/?utm_source=dlvr.it&utm_medium=mastodon

I’m from the 1900s 💀

In DNC Speech, Sanders Says Overturning “Citizens United” Should Be a Priority https://truthout.org/articles/in-dnc-speech-sanders-says-overturning-citizens-united-should-be-a-priority/?utm_source=dlvr.it&utm_medium=mastodon

People walked out of the trump rally in Wilkes-Barre, PA at the one hour mark lending credence to the completely legitimate theory that they were paid by the hour.

#HarrisWalz2024 (Crowd)Size matters

Thank you for contacting the abyss; your scream is very important to us.

any diode can be a light-emitting diode, once

Mask bans are bad even if only targeted to law breakers because they:

- Stigmatize masks and increase harassment of mask wearers

- Let police (who aren't doctors) subjectively decide who can wear a mask for health reasons

- Increase profiling

- Violate first amendment rights

When I was a university student, I applied for unpaid internships to practice my interviewing skills. If I received an offer, I always declined. I did this to get back at exploitative companies by wasting their time while practicing my interviewing skills for free.

The fake IRS scammers found my business number, so in case anyone needs to hear it: The IRS will not call you to tell you that you owe back taxes. The police will not call you and tell you that they have a warrant for your arrest. You cannot pay bail via gift cards over the phone.

Be safe out there 💜

A federal appellate court rules that California’s Age-Appropriate Design Code violates the First Amendment, a victory for free speech and privacy.
https://www.eff.org/deeplinks/2024/08/court-california-try-privacy-law-not-online-censorship
#privacy #censorship

NYT continues to be heavy on pro-Trump BS, light on news

"In a video circulated to members of the #police protective association via email, Grammas said I’m sure if you’re like me, you don’t want to have #biometric data in the hands of people that you don’t know,” https://www.reviewjournal.com/local/local-las-vegas/nfl-facial-recognition-policy-upsets-las-vegas-police-union-3128202/

Ukrainian armed forces are capturing more than 100 or 150 Russian soldiers every day, citing sources in the Ukrainian government

80% of all prisoners of war captured during the Kursk operation are conscripts - 18 year old Russian kids drafted into the military.

They, along with the Ukrainians, should be in school or raising a family.

ALL BECAUSE OF ONE MAN!
#AureFreePress #News #press #headline #Ukraine #Russia

“For years, #CrowdTangle has represented an industry best practice for real-time platform transparency. It has become a lifeline for understanding how #disinformation, hate speech, and voter suppression spread on Facebook, undermining civic discourse and democracy,” https://apnews.com/article/meta-crowdtangle-research-misinformation-shutdown-facebook-977ece074b99adddb4887bf719f2112a

When the company calls their home appliances "smart", what I hear is:

- they spent money on features I don't care about
- those features will be worse than standalone devices but will drive them out of market (looking at you TVs)
- the appliance is more likely to break
- my data is likely being sold to advertisers
- when the company loses interest in it and cut support, I will need to buy a new device

So no, I don't want "smart" home appliances.

When CHP was originally confronted about their lack of compliance with #AB481, the state's #military equipment transparency law, they initially said they aren't subject to state law. Now they say they are "working on it". https://lapublicpress.org/2024/08/chp-violating-state-law-equipment-ab481/

The trend of building surveillance into all new smart TVs is "incredibly invasive and little understood,” EFF’s Jacob Hoffman-Andrews told @arstechnica. "Nobody wants a snooping and snitching television, but lately that's all you can buy.” https://arstechnica.com/gadgets/2024/08/tv-industrys-ads-tracking-obsession-is-turning-your-living-room-into-a-store/